Mon | Closed |
Tue |
09:00 14:00 |
- |
12:00 16:00 |
Wed |
09:00 14:00 |
- |
12:00 16:00 |
Thu |
09:00 14:00 |
- |
12:00 16:00 |
Fri |
09:00 |
- |
12:00 |
Sat | Closed |
Sun | Closed |
Do you have any questions about the product, installation, delivery or payment? Our friendly and competent service is at your disposal
e-mail
info@maritimusboote.de
Phone number
+49 (0) 38231 402934
to disposal.
Friends / followers / pictures
Facebook: MaritimusYachting
twitter: MaritimusBoote
Picasa Web Albums: Maritime Boats
Skype Internet Phone Name:
maritime_boats
In stock
Incl:
flaps
cylinder
hydraulic unit
E kit
Hydraulic kit
operating unit
Display of location
We deliver everything from BENNETT
Many factors affect the choice of properly sized trim tabs, and the ultimate responsibility for selection is up to you, the boat owner. To help you decide, Bennett Marine offers you a few guidelines below.
General Guidelines
These sizing recommendations are based on average performance. Your choice may vary based on power, engine configuration, weight distribution, type of boat, and use. The greater the surface area, angle of deflection and/or speed of the water flowing under the trim tab, the greater the lift.
When making a choice between trim tab sizes, remember that the largest trim tabs that will comfortably fit on the transom will be the most efficient.
As a rule, choose at least one inch of trim tab span (per side) for every foot of boat length. (Examples: 22-foot boat = no less than 24" x 9", 36-foot boat = no less than 36" x 9".
Span = side to side measurement
Chord = fore to aft measurement
Whenever possible, choose a 9" chord trim tab, and gain lift through a longer span. The span of the trim tab has more of an effect on the amount of lift. However, a longer chord can be used effectively, and there are situations where you may need to use a 12" chord.
Measuring
Choose the approximate tab size for your boat using this sizing chart. Make sure the tabs will fit your transom using the diagrams below as a guideline. When measuring, disregard the strakes and follow the Vee of the hull.
Boat Length | Engine Configuration | Trim Tab Size (span x chord) |
15'-19' (4.5-5.8 m) | Single I/O, Single Outboard or Inboard | 12" x 9" (30 x 23 cm) |
17'-19' (5.2-5.8 m) | Single Outboard | 8" x 10" (20 x 25 cm) M80 |
19'-24' (5.8-7.3 m) | Single I/O, Single Outboard, or Inboard | 18" x 9" (46 x 23 cm) |
19'-24' (5.8-7.3 m) | Limited Transom Space or Extra Lift | 12" x 12" (30 x 30 cm) |
20'-23' (6.0-7.0 m) | Single I/O or Single Outboard | 10" x 12" (25 x 30 cm) M120 |
22'-27' (6.7-8.3 m) | Single I/O or Single Outboard | 24" x 9" (61 x 23 cm) |
22'-27' (6.7-8.3 m) | Twin I/O or Twin Outboard | 18" x 12" (46 x 30 cm) |
25'-30' (7.6-9.1 m) | Single I/O or Outboard | 30" x 9" (76 x 23 cm) |
25'-30' (7.6-9.1 m) | Limited Transom Space or Extra Lift | 30" x 12" (76 x 30 cm) |
25'-30' (7.6-9.1 m) | Twin I/O or Twin Outboard | 24" x 12" (61 x 30 cm) |
28'-34' (8.5-10.4 m) | Inboard | 36" x 9" (91 x 23 cm) |
28'-34' (8.5-10.4 m) | Limited Transom Space or Extra Lift | 36" x 12" (91 x 30 cm) |
28'-34' (8.5-10.4 m) | Twin I/O or Twin Outboard | 24" x 12" (61 x 30 cm) |
32'-38' (9.7-11.6 m) | Inboard | 42" x 9" (107 x 23 cm) |
32'-38' (9.7-11.6 m) | Limited Transom Space or Extra Lift | 42" x 12" (107 x 30 cm) |
36'-44' (11.0-13.4 m) | Inboard | 48" x 9" (122 x 20 cm) |
36'-44' (11.0-13.4 m) | Limited Transom Space or Extra Lift | 48" x 12" (122 x 30 cm) |
42'-50' (12.8-15.2 m) | Inboard | 54" x 9" (137 x 23 cm) |
50'-60' (15.2-18.3 m) | Inboard | 54" x 12" (137 x 30 cm) |
60'-65' (18.3-19.8 m) | Inboard | 60" x 12" (153 x 30 cm) |
65'-70' (19.8-21.3 m) | Inboard | 66" x 12" (168 x 30 cm) |
70'-80' (21.3-24.4 m) | Inboard | 72" x 12" (183 x 30 cm) |
Installation Requirements
Trim tabs should follow the Vee at the junction of the transom and the bottom of the boat. For maximum side to side control, trim tabs are generally mounted 3-4" from the chine and run towards the keel.
In case of inboards, the complete run from chine to keel may be utilized if it is an unbroken span of the same angle. Protrusions, such as strakes, may be bridged provided there is no change in angle on both sides.
On boats powered by inboard/outboards (I/O) or outboards it is necessary that the trim tabs not be placed too close (8" minimum) to the lower unit(s) to avoid disturbing the water flow to the propeller.
When to Use a 12" Chord
The 9" chord is used in most applications. However, in certain circumstances the 12" chord may be more effective:
Limited Transom Space - Boats with twin outboards or twin I/Os, or boats with transom configurations that limit trim tab span, can use 12" chord tabs to achieve maximum lift. Using the measuring guideline above, fit the maximum span tab and use the 12" chord.
Extra Lift - Slower boats (less than 15 mph), semi-displacement hulls, boats over 50 feet, outboard brackets or boats with any other feature that increases the need for lift aft benefit from the 12" chord. The 12" chord provides greater surface area, thereby utilizing more water flow and providing more lift.
Trim Tab Systems
BOLT Electric Trim Tab Systems
Trim Tab Systems
Standard (Classic) Hydraulic Trim Tab Systems
Trim Tab Systems
Sport (M80/M120) Limited Space Hydraulic Trim Systems
Trim Tab Systems
Premier Line XPT, BXT, SST Trim Tab Systems
Trim Tab Systems
Performance Sport Tab Systems
Trim Tab Systems
Self-Leveling Tabs
Indication & Controls
AutoTrim Pro (ELECTRIC & HYDRAULIC SYSTEMS)
Indication & Controls
Electronic Indicator Control Kit (HYDRAULIC SYSTEMS ONLY)
EIC5000
Indication & Controls
BOLT Control With Indication (ELECTRIC SYSTEMS ONLY)
BCI8000
Indication & Controls
BOLT Control Non-Indicator (ELECTRIC SYSTEMS ONLY)
BCN6000
Indication & Controls
Euro-Style Rocker Switch (HYDRAULIC SYSTEMS ONLY)
ES2000
Indication & Controls
BOLT Electric Rocker Switch Control (ELECTRIC SYSTEMS ONLY)
BRC4000
Actuators
Hydraulic Actuator Assembly
A1101A
Actuators
Short Hydraulic Actuator Assembly
A1200S
Actuators
Hydraulic Short M80/M120 Actuator (w/ Rivet Clearance)
A1200SRC
Actuators
BOLT Electric 12V Electric Actuator (Fixed Upper Hinge)
BEA2000
Actuators
BOLT 12-Volt Electric Actuator (Adjustable Upper Hinge)
BEA3000
Actuators
Premier Line SSA Actuator
SSA
Actuators
Premier Line BXA Actuator
BXA
Actuators
Hydraulic Actuator Assembly – External Line
A1101EX
Actuators
Hydraulic Actuator w/Sensor – Port for TPI or NMEA
A1101CP
Actuators
Hydraulic Actuator w/ sensor 10′ green wire – for EIC
A1101CSEIC
Actuators
Hydraulic Actuator w/ sensor – stbd (green) – for TPI or NMEA
A1101CS
Actuators
Hydraulic Actuator w/ sensor 10′ red wire – for EIC
A1101CPEIC
Trim Tab Assemblies
Trim Plane Assemblies
Various
Trim Tab Parts
Trim Plane Only (TPO)
Trim Tab Parts
Backing Plate Only (BPO)
https://bennetttrimtabs.com/imageDB-optimized/HingePlateOnly@0,25x.jpg
Trim Tab Parts
Hinge Plate Only (HPO)
Hydraulic Power Units (Pumps)
Hydraulic Power Unit
V351HPU1
Hydraulic Power Unit Parts
Hydraulic Power Unit – 24 Volt
V351HPU2
Hydraulic Power Units (Pumps)
Dual-Acting Hydraulic Power Unit
DAHPU
Dealer Service Kits
Dealer Service Kit (Hydraulic Systems)
DSKIT
Indication & Controls
NMEA 2000 Indicator Kit (HYDRAULIC SYSTEMS ONLY)
NMEA1
Conversion Kits
Lenco To Bolt Conversion Kit
BOLTLKCON
Conversion Kits
Bennett Hydraulic to BOLT Electric Conversion Kit
HYDBOLTCON
Conversion Kits
AutoTrim Pro Sensor Kit
ATPSENSTD
Indication & Controls
Auto Tab Control (HYDRAULIC SYSTEMS ONLY)
AC3000
Conversion Kits
Lenco to Bennett Hydraulic Conversion Kit
V351LK
Hatch Lifting Systems
Product | Note | Status | Price | ||
---|---|---|---|---|---|
|
|
1,078.00 € * |
Delivery weight: 12 kg
|
||
|
|
17,642.00 € * |
Delivery weight: 80 kg
|
||
|
|
498.00 € / pair(s) * |
Delivery weight: 12 kg
|
||
|
|
3,434.00 € * |
Delivery weight: 21 kg
|
||
* Prices incl. VAT, plus Shipping
Display accessory details
|
BENNETT V351HUC2E, hydraulic trim tabs with electronic control and control panel, 24V
1,078.00 €
*
Delivery weight: 12 kg
|
Trim Tab BCS MY5000 / Trim Tab TwinDisc MY5000, Yacht 31m, to 170t, 22kn, 2 hydraulic cylinders,24V
17,642.00 €
*
Delivery weight: 80 kg
|
Trim flaps Sport 30x30 cm, boats over 40kn, for BENNET systems
498.00 €
/ pair(s)
*
Delivery weight: 12 kg
|
LENCO high performance HP position correctors with double piston and control board
3,434.00 €
*
Delivery weight: 21 kg
|